Majacraft Spinning Wheel Drive Band

GENERAL PRODUCT SAFETY REGULATION (GPSR) INFORMATION

Intended Use:
Replacement spinning wheel drive band made to fit the specific spinning wheel brand and model identified in the selected product option.

Each drive band is cut and joined to the appropriate finished length for the listed wheel/model configuration.

Drive band material, diameter, and finished length may vary depending on the specific spinning wheel model selected.

This product is intended only for compatible spinning wheels and is not a universal drive band.


COMPATIBILITY

Before ordering and installation, confirm that:

• The selected drive band corresponds to the correct spinning wheel brand and model

• The wheel has not been modified in a way that changes the required drive band length, diameter, or routing

• The selected configuration matches the intended drive system

Do not install a drive band on an incompatible spinning wheel.

If the wheel manufacturer specifies a particular drive band type, diameter, routing method, or installation procedure, follow those instructions.


CAUTION — MOVING SPINNING WHEEL COMPONENT

The drive band moves continuously around the wheel and pulley system during normal operation.

• Keep fingers and hands away from the drive band while the wheel is moving

• Keep hair, loose clothing, jewelry, yarn, fiber, and other objects clear of the drive band and pulleys

• Stop the spinning wheel completely before installing, removing, repositioning, or inspecting the drive band

• Do not attempt to adjust the drive band while the wheel is rotating

• Keep children and pets away from the moving drive system

• This is a spinning wheel component, not a toy


BEFORE INSTALLATION

Inspect the drive band before installing it.

Do not install or use the drive band if:

• The material is cut, torn, badly abraded, cracked, or otherwise damaged

• The fused or joined area is separating

• The joint has a significant defect that could interfere with normal travel around the pulleys

• The band is excessively stretched or permanently deformed

• The band is contaminated with oil, chemicals, or material that could affect normal operation

• Any damage could cause the band to fail or leave the pulley system unexpectedly


INSTALLATION

Stop the spinning wheel completely before installation.

Install the drive band according to the normal routing for the specific spinning wheel model.

During installation:

• Confirm the band follows the correct pulley path

• Make sure the drive band is not twisted unless the spinning wheel design specifically requires a crossed band

• Keep the band away from sharp edges or damaged pulley surfaces

• Do not stretch the band excessively to force it into position

• Do not use sharp tools that could cut or nick the drive band

After installation, rotate the wheel slowly by hand and confirm that the band travels normally around the intended pulley surfaces.


DRIVE BAND TENSION

Use only enough tension for normal operation of the spinning wheel.

Excessive tension may:

• Increase wear on the drive band

• Place unnecessary load on wheel components

• Cause premature stretching or failure

• Affect normal spinning wheel operation

If the spinning wheel includes a tension adjustment system, follow the wheel manufacturer's instructions.


FUSED / JOINED AREA

The drive band includes a joined section that completes the continuous loop.

Before each use, inspect the joint for:

• Separation

• Cracking

• Excessive thinning

• Bulging or deformation

• Abrasion

• Damage caused by repeated pulley contact

A small visible joint may be a normal result of the joining process.

The joint should remain structurally secure and should pass through the wheel's drive system without catching or interfering with normal operation.

Discontinue use if the joint begins to separate or deteriorate.


BEFORE EACH USE

Before operating the spinning wheel:

• Inspect the drive band for wear or damage

• Confirm the band is correctly routed

• Confirm the band remains properly seated on the wheel and pulley system

• Check that the joint is intact

• Rotate the wheel slowly by hand if necessary to verify normal tracking

Do not operate the wheel if the drive band repeatedly leaves the intended pulley path or behaves abnormally.


SAFE USE

During spinning:

• Keep hands away from the moving band and pulleys

• Keep loose fiber and yarn from wrapping around the drive band

• Stop the wheel before clearing tangled fiber or yarn

• Stop the wheel before changing drive band routing or tension

• Do not intentionally touch or slow the moving band by hand

If the drive band comes off during operation, allow the wheel to stop completely before reinstalling it.


NORMAL WEAR

Drive bands are wear components and may gradually change with use.

Depending on the material and spinning conditions, normal wear may include:

• Surface polishing

• Minor abrasion

• Gradual stretching

• Changes in flexibility

• Wear at the joined area

Regular inspection is recommended.

Replacement should occur before wear progresses to the point where the drive band could fail during operation.


CARE

• Keep the drive band clean and dry

• Remove loose fiber, yarn, and debris as needed

• Avoid contact with sharp objects

• Avoid unnecessary exposure to oils, solvents, harsh cleaners, or chemicals unless specifically recommended for the drive band material

• Do not intentionally cut, sand, grind, or modify the band

• Inspect the joint periodically for wear


STORAGE

If the drive band is removed from the wheel:

• Store it in a clean, dry location

• Keep it away from sharp objects

• Do not place heavy objects on it

• Avoid excessive heat

• Avoid prolonged direct sunlight where practical

• Do not store the band under unnecessary tension

• Keep away from children and pets


DISCONTINUE USE

Stop using the drive band if:

• The joined area begins to separate

• The material becomes cracked, cut, torn, or severely abraded

• The band develops significant permanent deformation

• The band can no longer maintain normal tension

• The band repeatedly leaves the intended pulley path despite correct installation and wheel adjustment

• Damage develops that could cause unexpected drive band failure

Replace a worn or damaged drive band before continuing to operate the spinning wheel.